Solar charge controller with VECan port up to 48 V 250 V and 85 A in blue steel SmartSolar MPPT Tr Victron Energy

Product description:

• This is a solar charge controller, model SmartSolar MPPT 250/85 VE.Can Tr.
• It improves solar energy collection by up to 30%.
• Operates with a battery voltage down to 0 volts (as long as the cells are not sulphated or damaged).
• With VE.Can port to synchronise up to twenty-five units.
• With integrated Bluetooth smart.
  • Allows the controller to be configured, controlled and updated.
  • Up to ten units can be synchronised for parallel operation.
• With VE.Direct port for wired connection to a GX device, computers or other devices.
• Allows two or more maximum power points on the load voltage curve for partial cloudiness.
• It features SmartSolar algorithm, maximising energy harvesting by intelligently selecting the optimal MPP.
• Its maximum efficiency is over 99%, with full output current up to 40 °C.
• Equipped with programmable algorithm from Victron Energy software.
  • In addition, it includes eight pre-programmed algorithms that can be selected via the rotary switch.
• It has over-temperature protection and reduces power in case of high temperature.
• With short-circuit and reverse polarity protection on the PV panels.
• Features PV reverse current protection.
• Equipped with an internal temperature sensor.
  • Compensates the charging voltage (absorption and float) depending on the temperature.
• Compatible with external battery voltage and temperature sensors via Bluetooth.
• Remote on/off for connection to a VE.BUS BMS.
• Equipped with programmable relay to activate an alarm or other events.
• With TR type photovoltaic terminal, with one positive and one negative screw terminal.
• The battery voltage is 12/24/36/48 V., automatically selectable.
  • To select 36 V a software tool is required.
• The rated load current is 85 A.
• The minimum rated PV power is 1200 W and the maximum rated PV power is 4900 W.
• Maximum PV open circuit voltage of 250 V.
• Operates at temperatures between -30 and 60 °C (full rated output up to 40 °C).
• Absorption charging voltage of 14.4 / 28.8 / 43.2 / 57.6 V (adjustable).
• Float charge voltage of 13.8 / 27.6 / 41.4 / 55.2 V (adjustable).
• Equalising charge voltage of 16.2 V / 32.4 V / 48.6 V / 64.8 V (adjustable).
• Made of steel with blue finish.
• Dimensions are 295 mm wide, 216 mm high and 103 mm deep.
  • The terminals measure 35 mm².
• It has an IP43 degree of protection for the electronic components and IP22 in the connection area.
• It weighs 4.5 kg.
• Its safety standard is: EN/IEC 62109-1, UL 1741, CSA C22.2.

Optional:

• LCD display for control and monitoring.
  • This is a control LCD display for the BlueSolar and SmartSolar solar charge controllers.
  • It plugs into the front of the controller and the display is connected.
  • It can be used to control the solar charger.
  • It allows the display of live and historical data.
  • In addition, it can be used to configure the settings of the solar charger.
  • The display shows the following data.
    • Number reading with corresponding reading unit, such as V, A, W, kWh, h or °C/°F.
    • Type of reading, such as battery, PV or temperature.
    • State of charge and charging phase.
    • Warning indicator and connection indicator.
  • Buttons allow you to navigate through the solar charger readings and adjust the solar controller parameters.
    • Connect or back button.
    • Select or confirm button.
    • +" and "-" button to navigate through the items or increase/decrease the value.
  • This display is suitable for Victron Energy BlueSolar and SmartSolar MPPT 150V or 250V solar chargers.
  • The port connector of the display is RS232 9.
  • It measures 116 mm wide, 25 mm high and 50 mm deep.
  • Weighs 66 grams.

Options to choose from::