Smart solar charge controller 12V and 24V with 100V and 30A made of blue steel SmartSolar MPPT Victron Energy

Product description:

• This is a solar charge controller, model SmartSolar MPPT 100/30.
• It improves solar energy collection by up to 30%.
• It works with a battery voltage down to 0 volts (as long as the cells are not sulphated or damaged).
• With integrated Bluetooth smart.
  • Allows you to configure, control and update the controller.
• With VE.Direct port for wired connection to a GX device, computers or other devices.
• Allows two or more maximum power points on the load voltage curve, for cases of partial cloudiness.
  • Features BlueSolar algorithm, maximising energy harvesting by intelligently selecting the optimal MPP.
• Its maximum efficiency is more than 98%, with full output current up to 40 °C.
• Equipped with programmable algorithm from Victron Energy software.
  • In addition, it includes eight pre-programmed algorithms that can be selected via the rotary switch.
• It has over-temperature protection and reduces power in case of high temperature.
• With short-circuit and reverse polarity protection on the PV panels.
• Features PV reverse current protection.
• Equipped with an internal temperature sensor.
  • Compensates the charging voltage (absorption and float) depending on the temperature.
• Compatible with external battery voltage and temperature sensors via Bluetooth.
• Battery voltage is 12/24 V, automatically selectable.
• The nominal charging current is 30 A.
• The maximum rated PV power is 880 W.
• Maximum PV open circuit voltage of 100 V.
• Operates at temperatures between -30 and 60 °C (full rated output up to 40 °C).
• Absorption charging voltage of 14.4 / 28.8 / 43.2 / 57.6 V (adjustable).
• Float charge voltage of 13.8 / 27.6 / 41.4 / 55.2 V (adjustable).
• Made of steel with blue finish.
• Measures 186 mm wide, 130 mm high and 70 mm deep.
• It has an IP43 degree of protection in electronic components and IP22 in the connection area.
• It weighs 1.3 kg.
• Its safety standard is: EN/IEC 62109-1, UL 1741, CSA C22.2.

Optional:

• Venus GX electrical system monitoring controller.
  • This is a monitoring controller for Victron power systems.
  • You can configure the state of charge, voltage, load, off-peak times and monthly test runs.
  • Parameter reading can be done from the free VRM website for remote monitoring.
  • It has a customisable start/stop system.
  • Once connected to the internet all data is sent to the VRM.
    • If there is no internet connection, the Venus GX will store the data for 48 hours.
    • Allows a micro SD card or USB flash drive to increase data storage capacity.
  • Data can be converted offline with the Victron Connect App.
  • Internet connection can be made with an Ethernet cable via wifi.
  • Updates automatically if a software version is available (when connected to the internet).
  • It has an integrated Linux Venus OS operating system.
  • The fuel tank level inputs are resistive, so they must be connected to a resistive tank level transmitter.
    • Note: Victron does not supply such transmitters.
    • The tank level ports can be configured for compatibility with European tank level transmitters (0 - 180 Ohm).
  • Power supply voltage range is 8 - 70 Vdc.
  • Current consumption of 210 mA at 12 V, 110 mA at 24 V and 60 mA at 48 V.
  • With two isolated VE.Direct ports.
  • With two VE.Can ports with isolated parallel RJ45 sockets.
  • 2nd CAN interface non-isolated.
  • With two VE.Bus ports with parallel and isolated RJ45 sockets.
  • With two non-isolated USB host ports.
  • With one RJ 45 socket for 10 / 100 / 1000 MB.
  • Its dimensions are 143 mm wide, 45 mm high and 96 mm deep.
  • Operates in temperatures from -20 to 50 ºC.
  • Safety standard EN 60950-1:2005+A1:2009+A2:2013.
• Controller with display for monitoring electrical systems, Color Control GX.
  • You can configure the state of charge, voltage, load, off-peak times and monthly function tests.
  • Monitor and control locally on the Color Control GX itself.
  • Reading, monitoring and parameter setting can be done from the free VRM website.
  • It has a customisable start/stop system.
  • Once connected to the internet all data is sent to the VRM.
    • If there is no internet connection, it will store the data for 48 hours.
    • Allows a micro SD card or USB stick to increase data storage capacity.
  • Data can be converted offline with the Victron Connect App.
  • Internet connection can be made with an Ethernet cable via wifi.
  • Updates automatically if a software version is available (when connected to the internet).
  • It has an integrated Linux Venus OS operating system.
  • Modbus-TCP can be used to control electrical systems connected to the Color Control GX.
  • To obtain data from the VRM Portal, the VRM JSON API can be used.
  • The voltage range of the power supply is 8 - 70 Vdc.
  • The current consumption is given as follows:
    • 12 Vdc will draw a maximum of 245 mA with the display at full current.
    • 24 Vdc will draw a maximum of 125 mA with the display at full current.
    • 48 Vdc will draw 65 mA with the display at maximum current.
  • With two isolated VE.Direct ports.
  • With two VE.Can ports with isolated parallel RJ45 sockets.
  • With two VE.Bus ports with isolated parallel RJ45 sockets.
  • With two non-isolated USB host ports.
  • With one RJ 45 socket for 10 / 100 / 1000 MB.
  • Its dimensions are 120 mm wide, 130 mm high and 28 mm deep.
  • Operates in temperatures from -20 to 50 °C.
  • Safety standard EN 60950-1:2005+A1:2009+A2:2013.

Options to choose from::