Victron Energy BlueSolar MPPT 12 and 24 V solar charge controller with 75 Vdc and 15 A made of blue steel

Product description:

• This is a solar charge controller, model BlueSolar MPPT 75/15.
• It collects energy from the solar panel and stores it in the batteries quickly.
• It monitors the output voltage and current of the solar panels, ensuring collection and storage even on cloudy days.
• It has a charging output that will disconnect when the battery is overcharged or when it reaches a pre-set voltage.
• It is protected against short circuits.
• With BatteryLife system: algorithm that monitors the state of charge of the battery to extend battery life, allowing collection up to almost 100% of energy and preventing battery failure due to inaccuracies in the measurement.
  • This algorithm is programmable with Victron Energy software.
• It is equipped with a day and night timer.
• In addition, it allows the brightness to be regulated.
• It is compatible with GX devices and smartphones or Bluetooth devices. For the latter, a VE.Direct Bluetooth Smart dongle is required.
• The battery voltage is 12/24 V.
• The nominal charging current is 15 A.
• The continuous charging current is 15 A.
• The maximum rated power is 440 W.
• Maximum photovoltaic open circuit voltage of 75 Vdc.
• Operates at temperatures between -30 and 60 ºC (full rated power up to 40 ºC).
• Made of steel with blue finish.
• Its measurements are 113 mm wide, 100 mm high and 40 mm deep.
• It has an IP43 degree of protection in electronic components and IP22 in the connection area.
• It weighs 0.5 kg.
• Its safety standard is: EN/IEC 62109-1, UL 1741, CSA C22.2.

Optional:

• Venus GX electrical system monitoring controller.
  • This is a monitoring controller for Victron power systems.
  • You can configure the state of charge, voltage, load, off-peak times and monthly test runs.
  • Parameter reading can be done from the free VRM website for remote monitoring.
  • It has a customisable start/stop system.
  • Once connected to the internet all data is sent to the VRM.
    • If there is no internet connection, the Venus GX will store the data for 48 hours.
    • Allows a micro SD card or USB flash drive to increase data storage capacity.
  • Data can be converted offline with the Victron Connect App.
  • Internet connection can be made with an Ethernet cable via wifi.
  • Updates automatically if a software version is available (when connected to the internet).
  • It has an integrated Linux Venus OS operating system.
  • The fuel tank level inputs are resistive, so they must be connected to a resistive tank level transmitter.
    • Note: Victron does not supply such transmitters.
    • The tank level ports can be configured for compatibility with European tank level transmitters (0 - 180 Ohm).
  • Power supply voltage range is 8 - 70 Vdc.
  • Current consumption of 210 mA at 12 V, 110 mA at 24 V and 60 mA at 48 V.
  • With two isolated VE.Direct ports.
  • With two VE.Can ports with isolated parallel RJ45 sockets.
  • 2nd CAN interface non-isolated.
  • With two VE.Bus ports with parallel and isolated RJ45 sockets.
  • With two non-isolated USB host ports.
  • With one RJ 45 socket for 10 / 100 / 1000 MB.
  • It measures 143 mm wide, 45 mm high and 96 mm deep.
  • Operates in temperatures from -20 to 50 ºC.
  • Safety standard EN 60950-1:2005+A1:2009+A2:2013.
• Controller with display for monitoring electrical systems, Color Control GX.
  • You can configure the state of charge, voltage, load, off-peak times and monthly function tests.
  • Monitor and control locally on the Color Control GX itself.
  • Reading, monitoring and parameter setting can be done from the free VRM website.
  • It has a customisable start/stop system.
  • Once connected to the internet all data is sent to the VRM.
    • If there is no internet connection, it will store the data for 48 hours.
    • Allows a micro SD card or USB memory stick to increase data storage capacity.
  • Data can be converted offline with the Victron Connect App.
  • Internet connection can be made with an Ethernet cable via wifi.
  • Updates automatically if a software version is available (when connected to the internet).
  • It has an integrated Linux Venus OS operating system.
  • Modbus-TCP can be used to control electrical systems connected to the Color Control GX.
  • To obtain data from the VRM Portal, the VRM JSON API can be used.
  • The voltage range of the power supply is 8 - 70 Vdc.
  • The current consumption is given as follows:
    • 12 Vdc will draw a maximum of 245 mA with the display at full current.
    • 24 Vdc will draw a maximum of 125 mA with the display at full current.
    • 48 Vdc will draw 65 mA with the display at maximum current.
  • With two isolated VE.Direct ports.
  • With two VE.Can ports with isolated parallel RJ45 sockets.
  • With two VE.Bus ports with isolated parallel RJ45 sockets.
  • With two non-isolated USB host ports.
  • With one RJ 45 socket for 10 / 100 / 1000 MB.
  • Its dimensions are 120 mm wide, 130 mm high and 28 mm deep.
  • Operates in temperatures from -20 to 50 °C.
  • Safety standard EN 60950-1:2005+A1:2009+A2:2013.

Options to choose from::