Multiplus Victron Energy 48 V, 800 VA multifunctional power inverter made of steel and blue ABS plastic Multiplus Victron Energy

Product description:

• This is a pure wave multifunctional power inverter, MultiPlus model.
• Intelligent power and high power start-up.
• It features:
  • A powerful sine wave inverter.
  • A battery charger with adaptive technology.
  • A high-speed alternating current transfer switch.
• Up to six MultiPlus can be used in parallel to achieve higher power.
• Allows configuration of three units for three-phase output.
• Features a multi-control panel where a maximum current from the generator or pontoon can be set.
  • The inverter will consider other AC loads and use the excess power for charging. In this way it will avoid overloading the generator or the dock.
• Its Power Assist technology will compensate for the lack of power from the grid or generator when a power peak is required for a short period of time.
  • When the load is reduced, the excess power is reused to charge the battery.
• The main power output features "variable load" software.
  • This software fine-tunes the automatic three-stage process to match battery conditions.
  • It also adds a fourth stage for extended float periods.
  • The MultiPlus can charge a second battery using a limited charge output.
• It is equipped with a programmable relay that is configured by default as an alarm relay.
  • This relay will be de-energised in the event of an alarm or pre-alarm, i.e. when the inverter overheats, the input ripple is too high or the battery is undervoltage.
• It has a three-pole remote on/off connector.
• This model allows configuration of settings via DIP switches:
  • Remote switch.
  • Battery charge voltage.
  • Inverter frequency.
  • Search mode.
• A GX device can be installed to connect to the internet.
• It is made of steel and ABS plastic with a blue finish.
• It measures 240 mm wide, 360 mm high and 100 mm deep.
• The nominal voltage is 48 V.
• The load current of the inverter is 16 A.
• The apparent power is 800 VA (volt-amperes).
• Its peak power is 1600 W.
• Its input voltage range is 9.5 to 17 / 19 to 33 / 38 to 66 V.
• The output voltage is 230 Vac.
• Frequency is 50 Hz.
• The charger has an input of 187 - 265 Vac.
  • Charging current is 9 A.
  • Frequency 45 - 65 Hz.
• It has IP21 protection, protection against vertical water dripping.
• Weighs 6.4 kg.
• Safety standard: EN-IEC 60335-1, EN-IEC 60335-2-29, EN 62109-1.

Optional:

• Venus GX electrical system monitoring controller.
  • This is a monitoring controller for Victron power systems.
  • You can configure the state of charge, voltage, load, off-peak times and monthly test runs.
  • Parameter reading can be done from the free VRM website for remote monitoring.
  • It has a customisable start/stop system.
  • Once connected to the internet all data is sent to the VRM.
    • If there is no internet connection, the Venus GX will store the data for 48 hours.
    • Allows a micro SD card or USB flash drive to increase data storage capacity.
  • Data can be converted offline with the Victron Connect App.
  • Internet connection can be made with an Ethernet cable via wifi.
  • Updates automatically if a software version is available (when connected to the internet).
  • It has an integrated Linux Venus OS operating system.
  • The fuel tank level inputs are resistive, so they must be connected to a resistive tank level transmitter.
    • Note: Victron does not supply such transmitters.
    • The tank level ports can be configured for compatibility with European tank level transmitters (0 - 180 Ohm).
  • Power supply voltage range is 8 - 70 Vdc.
  • Current consumption of 210 mA at 12 V, 110 mA at 24 V and 60 mA at 48 V.
  • With two isolated VE.Direct ports.
  • With two VE.Can ports with isolated parallel RJ45 sockets.
  • 2nd CAN interface non-isolated.
  • With two VE.Bus ports with parallel and isolated RJ45 sockets.
  • With two non-isolated USB host ports.
  • With one RJ 45 socket for 10 / 100 / 1000 MB.
  • It measures 143 mm wide, 45 mm high and 96 mm deep.
  • Operates in temperatures from -20 to 50 ºC.
  • Safety standard EN 60950-1:2005+A1:2009+A2:2013.
• Controller with display for monitoring electrical systems, Color Control GX.
  • You can configure the state of charge, voltage, load, off-peak times and monthly function tests.
  • Monitor and control locally on the Color Control GX itself.
  • Reading, monitoring and parameter setting can be done from the free VRM website.
  • It has a customisable start/stop system.
  • Once connected to the internet all data is sent to the VRM.
    • If there is no internet connection, it will store the data for 48 hours.
    • Allows a micro SD card or USB stick to increase data storage capacity.
  • Data can be converted offline with the Victron Connect App.
  • Internet connection can be made with an Ethernet cable via wifi.
  • Updates automatically if a software version is available (when connected to the internet).
  • It has an integrated Linux Venus OS operating system.
  • Modbus-TCP can be used to control electrical systems connected to the Color Control GX.
  • To obtain data from the VRM Portal, the VRM JSON API can be used.
  • The voltage range of the power supply is 8 - 70 Vdc.
  • The current consumption is given as follows:
    • 12 Vdc will draw a maximum of 245 mA with the display at full current.
    • 24 Vdc will draw a maximum of 125 mA with the display at full current.
    • 48 Vdc will draw 65 mA with the display at maximum current.
  • With two isolated VE.Direct ports.
  • With two VE.Can ports with isolated parallel RJ45 sockets.
  • With two VE.Bus ports with isolated parallel RJ45 sockets.
  • With two non-isolated USB host ports.
  • With one RJ 45 socket for 10 / 100 / 1000 MB.
  • Its dimensions are 120 mm wide, 130 mm high and 28 mm deep.
  • Operates in temperatures from -20 to 50 °C.
  • Safety standard EN 60950-1:2005+A1:2009+A2:2013.

Options to choose from::