CM LCD display tester PCE Instruments

Product description:

• Fixed aperture clamp meter for AC and DC current, resistance, temperature and capacitance measurements.
• It integrates a 4000-digit backlit LCD display where the data is displayed.
• Low battery and, if available, low voltage and overload are also indicated.
• The clamp has a fixed opening of 17 mm.
• It also has two measuring tips.
• It has an automatic switch-off after 30 minutes of non-use.
• It is powered by two 1.5 V batteries.
• It is a compact product and therefore ideal for technicians and specialists.
• Delivery includes 1 ammeter, 2 measuring tips, 2 test leads, 1 thermocouple adapter, 1 thermocouple type K, 2 AAA batteries, and 1 manual.

Technical data:

• DC voltage measuring range: from 4, 40, 400 and 600 V DC.
  • Accuracy: ± 1.2, 1.5, 1.5 and 2 % of the value plus 2 d, respectively.
  • Resolution: 1, 10 and 100 mV and 1 V, respectively.
  • Input impedance: 10 MΩ.
  • Overvoltage protection: 600 V DC
    and 600 V AC RMS.
• Measurement range of AC voltage: 4, 40, 400 and 600 V DC.
  • Accuracy: ± 1,2 (+2d); 1,5,; 1,5 and 2 % of the value plus 2 d, respectively.
  • Resolution: 1, 10 and 100 mV and 1 V, respectively.
  • Input impedance: 10 MΩ.
  • Overvoltage protection: 600 V DC
    and 600 V AC RMS.
  • Frequency: 50 to 400 Hz.
• Measuring range of alternating current: 200 A AC.
  • Accuracy: ± 3,0 % of value + 5 d.
  • Resolution: 100 mA.
  • Overload protection: 200 A AC.
  • Frequency range: 50 to 60 Hz.
• Resistance measurement range: 400 Ω; 4, 40 and 400 KΩ; 4 and 40 MΩ.
  • Accuracy: 1; 1.5; 1.5; 1.5; 1.5; 2.5; 3.5 % of the value plus 4 d respectively.
  • Resolution: 0.1, 1, 10 Ω; 1 and 10 KΩ respectively.
  • Overload protection: 250 V DC or 250 AC RMS.
• Frequency measurement range: 40 and 400 Hz; 4, 40 and 400 KHz; 10 MHz.
  • Accuracy: ± 3,0 % of the value + 5 °C or 8 °F.
  • Resolution: 0.01 to 1 °C or °F.
  • Overload protection: 300 V DC and 300 AC RMS.
• Temperature measuring range: -20 to 760 °C or 4 to 4000 °F.
  • Accuracy: 1; 1.5; 1.5; 1.5; 1.5; 2.5; 3.5 % of the value plus 4 d respectively.
  • Resolution: 0.1, 1, 10 Ω; 1 and 10 KΩ respectively.
  • Overload protection: 250 V DC or 250 AC RMS.
  • Type K connection.
• Duty cycle measurement range: 0.1 to 99.9 %.
  • Accuracy: ±1,2 % of the value ± 2 d
  • Resolution: 0,01 %.
  • Sensitivity: 1 V RMS.
  • Pulse width: > 100 µs,
  • Overload protection: 300 V DC and 300 AC RMS.
• Capacitance measuring range: 4, 40 and 400 nF and 4, 40 and 400 µF.
  • Accuracy: ± 5 % of the value over 20 d for 1 nF. For 400 µF ± 3 % of the value + 10 d. The rest ± 3 % of the value over 5 d.
  • Resolution: 0,1; 1; 10 and 100 nF and 1 and 10 µF, respectively.
  • Overload protection: 250 V DC or 250 AC RMS
• Test function:
  • Diode test: 0.5 mA.
  • Inverse voltage: 1.5 V.
  • Open circuit voltage: 0.5 V.
• Alert: noise when resistance
• Updating values: 3 Hz rate.
• Input impedance: 10 MΩ.
• Power supply: 2 x 1.5 V AAA batteries.
• Pollution degree: 2.
• This current clamp meter complies with the following standards: IEC1010-1 (2001); CAT II 1000 V and CAT III 600 V.

SKU: 4250348718259, PCECM, 3